How to make your own homemade water pipes, whether you’re making them in your kitchen or your garage, is easy and you’ll be surprised how much you can do with a bit of creativity.

    But, it is worth noting that you need a little bit of wood for this, as it can be quite expensive.

    Here’s a quick tutorial to get you started.

    1.

    Purchase a box of nails and glue The first step is to purchase a box and a few nails to start.

    You’ll need these nails for attaching your pipes to the ceiling and other objects.

    The boxes will hold up to about two metres of wood.

    You can buy these nails in any number of sizes, from a single foot to a large four metres.

    2.

    Measure your length and width 1.

    Measure the length of the pipe you want to make and the length you want the pipe to hang from.

    This will help you choose a suitable length for the pipe.

    You will need to measure the length before you start the cut.

    2a.

    Measure across the bottom of the box you want your pipe to sit on.

    Measure around the bottom and down the length.

    2b.

    Measure at the end of the length (around the top) and the middle (around down the middle).

    You will want to measure this at the top and bottom of each section of pipe.

    3.

    Cut the length and diameter of the two pieces of wood You can cut the two sections of pipe into two pieces, using a pair of scissors or a hacksaw.

    This is easier to do with an 8mm cutting saw.

    The cut is about 10cm (4 inches) long.

    3a.

    Cut a 10cm piece of pipe with an 11cm (3 inches) cutting saw and attach it to the box.

    The two pieces will hang from the ceiling.

    3b.

    Cut an 8cm (2 inches) piece of PVC pipe, using an 8.5mm (2.8 inches) saw.

    Attach it to each pipe and then attach it back to the boxes.

    3c.

    Cut two 4cm (1 inch) pieces of PVC from a 5cm (19 inches) pipe and attach them to the boards.

    4.

    Cut six pieces of 4cm length of PVC and attach each piece to each box.

    You’re now ready to begin the construction of your pipe.

    Make sure you have a good supply of glue, as this is important to hold the pipes in place.

    4a.

    Use a 1mm (0.5 inch) piece to glue the two lengths together.

    4b.

    Place the two boards back together and attach the two pipes to each end of each board.

    You should have two pieces with one end connected to the other, with the end between the pipes sitting above the ceiling, and the other end attached to the floor.

    5.

    Install your pipe 5.

    Put the pieces together using your 2mm (1.5inch) pipe, and attach one of them to each of the four boxes.

    This should be the only way you can get a proper seal.

    You may want to add a piece of 1mm PVC pipe to each board as well.

    6.

    Use the 2mm PVC piece to attach each of your pipes.

    This can be done with a 5mm (16 inches) or 8mm (4.5 inches) cut from a piece.

    You are now ready for the job.

    Make the pipe look finished!

    7.

    Attachment screws on each end Make sure the screws are snug and secure to the pipe before attaching the two ends.

    To attach the pipe, you’ll need a small flathead screwdriver.

    The screws should be snug and easy to find, so you’ll want to get one that has a wide base and a thin screw head.

    This may be difficult to find on eBay, but if you’re going to be buying from someone who does, it should be something like this.

    I bought mine at Home Depot for £4.50.

    8.

    Cut and glue the pipe You now have a nice pipe, but what do you do with it?

    Here are a few tips to get your pipe going.

    1a.

    Attaching a plastic or plastic rod to the end allows the pipe’s end to slide back and forth between the boards, which will help to keep the pipes secure.

    You won’t need a plastic rod as the metal rod can be found in many plumbing supply stores.

    You don’t need to make a huge pipe, just a pipe with a small amount of wood attached.

    1b.

    You might find it helpful to cut the pipe so that the wood can be easily attached to each section.

    You could also attach the pipes ends to the pipes walls with some screws, but I found that the wooden end works best, as the wood will be easy to hold.

    2c.

    You need to keep an eye on the pipe in order to keep it in place, as some pipes are quite slippery, and this can be a problem.

    Attaches the pipe with screws

    RELATED ARTICLES